Vorshlag Motorsports Forum

Vorshlag Motorsports Forum (http://www.vorshlag.com/forums/index.php)
-   Engine Swap Discussions (http://www.vorshlag.com/forums/forumdisplay.php?f=42)
-   -   E36 LS1 Beta (http://www.vorshlag.com/forums/showthread.php?t=4813)

Fair! 02-16-2007 01:47 AM

E36 LS1 Beta
 
Updates for Feb 15, 2007: We've been swamped with orders, which has been kept us going into the wee hours of the morning many nights, but did manage to get some work in on the LS1 project 3 nights in the past week. Latest pics start here.

We have optimized the driveline angles (where the rear diff flange and transmission flanges are equal-but-offsetting angles, for proper U-joint operation) and shifter ergonomics by raising the transmission in the tunnel significantly. This was helped by removing the insulation under the tunnel and trimming the shifter hole "ever so slightly". An adjustable offset/angle shifter (from McLeod) will put everything perfectly within arms reach. After seeing several LS1/T56 swaps in magazines and on some car shows, each of which required major tunnel surgery or complete tunnel removal & replacement, this BMW chassis really does swallow this drivetrain quite well. :)

http://www.vorshlag.smugmug.com/photos/129947390-S.jpghttp://www.vorshlag.smugmug.com/photos/129947432-S.jpg

After the drivetrain was in the final final location, we finished the LS1 block mounting plates, procured the right bolts (M10x1.5x30mm SHCS), then built the top plates for our Competition Motor Mounts where the lateral supports will land. A few nights ago we made the templates, and tonight we cut the lateral steel pieces and tacked them in place. So one side is fabbed (still needs a gusset) and the other is almost there.

I can say this - we need a plasma cutter. Cutting these curved shapes with a band saw is a whip! The production pieces will be water jet or laser cut (then welded in a jig), of course. Bolt-in motor mounts that exceed factory strength and quality is the goal. Oh yes. if we didn't post it yet, we will have both Nylon and Polyurethane inserts for these motor mounts - so you can dial-back engine vibration if you desire, or go for the instant throttle response of our racing mounts. :D

Enjoy:

http://www.vorshlag.smugmug.com/photos/129947053-S.jpghttp://www.vorshlag.smugmug.com/photos/129947310-S.jpg
http://www.vorshlag.smugmug.com/photos/129944114-S.jpghttp://www.vorshlag.smugmug.com/photos/129944313-S.jpg
http://www.vorshlag.smugmug.com/photos/129945199-S.jpghttp://www.vorshlag.smugmug.com/photos/129944420-S.jpg
http://www.vorshlag.smugmug.com/photos/129944520-S.jpghttp://www.vorshlag.smugmug.com/photos/129944820-S.jpg

Bolt-in transmission crossmember/mount is next. Once that is finalized, we have the necessary diff-side flange parts that will now allow us to measure for the custom driveshaft and get that on order. Lots of brake fittings and hardline on the way from Goodridge for the ABS relocation. We'll tackle the fuel line & pump upgrade next (stock lines and pump will not support projected 650 hp).

Thanks to McCall for volunteering on more than one occasion in the past week. :)

HIDGolf 02-16-2007 01:33 PM

Re: E36 LS1 Beta
 
Keep it coming guys!

duck 02-16-2007 04:27 PM

Re: E36 LS1 Beta
 
Love the look of the 2.0 motor mounts! Kinda like the spokes on the old 18" sport wheels. I think these are them:
http://www.bmwmregistry.com/faq/E34-...poke_Wheel.jpg

duck 02-16-2007 04:31 PM

Re: E36 LS1 Beta
 
Love the look of the 2.0 engine mounts! Very professional and cool looking. They remind me of the M Parallel wheel spokes from the 740 sport package a little bit. Tie-ins like that would attract the pimps as well as the performers. Throw in a third strut and powdercoat them M colors for an addition fee. :-)

HIDGolf 02-16-2007 06:14 PM

Re: E36 LS1 Beta
 
By the way, does the beta car have any deadline? Like SEMA or a specific race?

hancheyb 02-16-2007 06:32 PM

Re: E36 LS1 Beta
 
Quote:

Originally Posted by HIDGolf
By the way, does the beta car have any deadline? Like SEMA or a specific race?

July 27th. GRM Ultimate Track Car Challenge. :)

HIDGolf 02-18-2007 10:36 PM

Re: E36 LS1 Beta
 
Have you guys made a cardomain page per the rules?

http://grassrootsmotorsports.com/new...-challenge.php

Fair! 02-19-2007 12:32 AM

Re: E36 LS1 Beta
 
Quote:

Originally Posted by HIDGolf
Have you guys made a cardomain page per the rules?

http://grassrootsmotorsports.com/new...-challenge.php

Not yet, but it isn't due till June 1st I believe. Oops, Hanchey here, I was logged in on Fair's PC. Doh!

Fair! 02-19-2007 01:10 AM

Re: E36 LS1 Beta
 
Feb 18, 2007: We were slammed this weekend doing machine work on a big run of camber plate parts (welding, drilling, boring, etc) but we did manage to get the pieces cut and tack welded for the the pass. side LS1 motor mount as well as parts of the trans cross member machined.

http://vorshlag.smugmug.com/photos/130610698-S.jpghttp://vorshlag.smugmug.com/photos/130610729-S.jpg

Kept the same arched shape as the driver's side, for matching aesthetics more than anything. The arch helped on the driver's side to clear the steering shaft rag joint. More pics here. Owner came by for the shifter "fitting" and we test fit dual 3" pipes out back - which didn't fit well. Going to stick with a dual 3" merged mid-way down the chassis into single 4" pipe and muffler.

Shortcutsleeping 02-19-2007 11:47 AM

Re: E36 LS1 Beta
 
The grm UTC will be tough. A well-driven high HP Z06 will be tough to beat unless you bring a full-on car.

Or is the goal to show up and beat all the non-heavy duty guys and get some press for vomo and the ls1 kit?


Costas


All times are GMT -5. The time now is 09:29 PM.

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.